MS-520 Scan HeadUser's ManualP/N 83-000500 Rev E
Chapter 1 Introduction1-4MS-520 Scan Head User’s Manual1–IntroductionSpot OptionsThe laser beam on the scan head can be projected on the bar code labe
FIS OptionsMS-520 Scan Head User’s Manual1-51–IntroductionSingle Line OptionScan beams projected across a label appear as a single scan line, as shown
Chapter 1 Introduction1-6MS-520 Scan Head User’s Manual1–IntroductionThe Scanning SystemFigure 1-6 shows a possible scanning system setup. Figure A-6
ChapterMS-520 Scan Head User’s Manual2-12–SetupSetupChapter ContentsSetup Goals ...
Chapter 2 Setup2-2MS-520 Scan Head User’s Manual2–SetupSetup GoalsTo achieve the desired number of scans required by the application, scan heads must
Label OrientationMS-520 Scan Head User’s Manual2-32–SetupLabel OrientationIf the bar code label bars are parallel to the direction of travel, as shown
Chapter 2 Setup2-4MS-520 Scan Head User’s Manual2–SetupAngled Picket Fence Orientation The problems associated with picket fence can be minimized by s
Tilt, Skew, and PitchMS-520 Scan Head User’s Manual2-52–SetupTilt, Skew, and PitchTilt refers to the label rotation, relative to the scan head, as it
Chapter 2 Setup2-6MS-520 Scan Head User’s Manual2–SetupRead RangesA label must be within the read range—the zone, as measured from the front of the sc
Read RangesMS-520 Scan Head User’s Manual2-72–SetupTable 1-4 MS-520 Read Ranges and Scan Widths** Performance may vary slightly for raster units.To a
iiMS-520 Scan Head User’s ManualInformation and specifications in this manual are subject to change without notice.Copyright © 2007by Microscan System
Chapter 2 Setup2-8MS-520 Scan Head User’s Manual2–SetupCalculating the Number of ScansTo ensure reliable scanning, it is recommended that a minimum of
Calculating the Number of ScansMS-520 Scan Head User’s Manual2-92–SetupUse the formula1 suitable for your application to predict the number of scans e
Chapter 2 Setup2-10MS-520 Scan Head User’s Manual2–SetupComparing Label Orientation Calculations When evaluating ladder versus picket fence orientatio
ChapterMS-520 Scan Head User’s Manual3-13–InstallationInstallationChapter ContentsMounting the Scan Head...
Chapter 3 Installation3-2MS-520 Scan Head User’s Manual3–InstallationMounting the Scan HeadThe MS-520 scan head can be mounted directly to a mounting
CablingMS-520 Scan Head User’s Manual3-33–InstallationCablingThe standard cable supplied with a MS-520 scan head is 6 feet (1.83 cm) in length, wired
Chapter 3 Installation3-4MS-520 Scan Head User’s Manual3–InstallationOperational Tips Do:• Check the label for readability in the visible (670 nm) or
MS-520 Scan Head User’s ManualA-1AppendicesAppendicesContentsAppendix A — Scan Head Specifications...A-2Appen
AppendicesA-2MS-520 Scan Head User’s ManualAppendicesAppendix A — Scan Head SpecificationsExcept where otherwise noted, the following specifications a
Scan Head SpecificationsMS-520 Scan Head User’s Manual A-3AppendicesLaser LightOptical Composite read ranges for several Code 39 narrow-bar-width size
MS-520 Scan Head User’s ManualiiiTable of ContentsList of Illustrations ...
AppendicesA-4MS-520 Scan Head User’s ManualAppendicesElectricalPower Requirements:+12 VDC @ 50 mA maximum, 20 mV p-p maximum allowed ripple-12 VDC @ 3
Optional EquipmentMS-520 Scan Head User’s Manual A-5AppendicesAppendix B — Optional EquipmentMounting Plate KitPart Number: 98-500002 To mount the sca
AppendicesA-6MS-520 Scan Head User’s ManualAppendicesUniversal StandThe Microscan Universal Stand is available in 4-inch, 6-inch, and 10-inch flex mod
Glossary of TermsMS-520 Scan Head User’s Manual A-7AppendicesAppendix C — Glossary of TermsBar Code. Data that has been encoded into an array of paral
AppendicesA-8MS-520 Scan Head User’s ManualAppendicesRound Spot. The standard laser beam as it appears on the label being scanned, sometimes slightly
MS-520 Scanner User’s ManualI-1IndexAAmbient Light Immunity A-4Angled Picket Fence Orientation 2-4Approvals vCCable Length A-2Cabling 1-6, 3-3Calcula
I-2 MS-520 Scanner User’s ManualIndexIndexSpot Options 1-4Standard features 1-2TTemperature A-4Tilt 2-5Tilt (definition) A-8UUniversal Stand A-6WWarni
ivMS-520 Scan Head User’s ManualList of IllustrationsFigure 1-1 Back View of MS-520 Scan Head Scanning a Label ... 1-2Figure 1-2 Laser Be
MS-520 Scan Head User’s ManualvApprovalsThis equipment is approved for use by the following organizations:• CDRH (Center for Devices & Radiologica
viMS-520 Scan Head User’s ManualSafety LabelsBack LabelTop Label1201 S.W . 7th St. Renton, W A 98055PRODUCT CONFORMS TO DHHS 21
ChapterMS-520 Scan Head User’s Manual1-11–IntroductionIntroductionChapter ContentsMS-520 Scan Head Description...
Chapter 1 Introduction1-2MS-520 Scan Head User’s Manual1–IntroductionMS-520 Scan Head DescriptionThe MS-520 scan heads use a high-speed, ten-sided spi
FIS OptionsMS-520 Scan Head User’s Manual1-31–IntroductionFIS OptionsFIS (Final Instruction Sheet) numbers are assigned to each customer order. The MS
Comments to this Manuals