Microscan MS-2 User Manual download pdf (Page 32)

Home
Microscan
Bar code readers
MS-2
User Manual

Download
Share

Sharing
Add to my manuals
Print

2-12 MS-2 CCD Reader User’s Manual

Autoconnect

•

If your RS-232 connection attempt fails, you can use

Autoconnect

to establish a connection

between the reader and the host.

• If your communications port is not the default COM1, use the dropdown menu to change

your port.

When you are connected, you will see the green connection indicator in the status bar at

the bottom right of your screen:

• Once you have

chosen the correct

port, click Start to

connect.

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 124 125

MS-2 CCD Reader 1
User’s Manual 1
Disclaimer 2
Latest Manual Version 2
Technical Support 2
What Is Covered? 3
What Is Excluded? 3
Limitation of Liability 3
Table of Contents 4
About the MS-2 CCD Reader 6
About This Manual 6
Highlighting 6
Host Communications 6
Warning and Caution Summary 7
Statement of RoHS Compliance 9
MS-2 CCD Reader User’s Manual 10
1 Quick Start 11
Step 1 — Check Hardware 12
Step 2 — Connect the System 13
Step 3 — Install ESP 14
Step 4 — Select Model 15
Step 5 — Autoconnect 16
Step 6 — Position the Reader 17
Step 7 — Configure the Reader 18
Saving Options 19
Save Configuration in ESP 20
2 Using ESP 21
Application Mode 23
Menu Toolbar 24
Preferences > General Tab 26
Preferences > Terminal Tab 27
Sizing Information 28
Preferences > Advanced Tab 29
(cont.) 30
Connect to Readers via TCP/IP 30
Use Default Storage Location 30
Document Memo 31
Model Memo 31
Autoconnect 32
Autoconnect (cont.) 33
Navigating in ESP 35
Send/Receive Options 36
Defaulting 37
Advanced Options 37
3 Communications 39
Communications by ESP 40
Host Port Connections 42
Host Port Protocol 43
Preamble 44
Postamble 45
4 Read Cycle 47
Read Cycle by ESP 48
Read Cycle Serial Commands 49
MS-2 Read Cycle Overview 50
Number of Symbols 51
Trigger Mode 53
External Edge 54
Serial Data 54
Serial Data and Edge 54
No Decode Timeout 59
Decodes Before Output 60
No Read Message 61
Reader Setup 62
5 Symbologies 63
Symbologies by ESP 64
Symbologies Serial Commands 65
Full ASCII Set (Code 39) 67
Symbol Length (Codabar) 69
Interleaved 2 of 5 70
Minimum Length 71
Fixed Length 71
Code 128/EAN 128 72
GS1 DataBar (RSS) 74
MSI Code 75
Plessey Code 76
Industrial 2 of 5 77
UPC-A Status (UPC/EAN) 79
UPC-E Status (UPC/EAN) 79
EAN-8 Status (UPC/EAN) 79
EAN-13 Status (UPC/EAN) 80
UPC-A as EAN-13 (UPC/EAN) 81
UPC-E as UPC-A (UPC/EAN) 81
EAN-8 as EAN-13 (UPC/EAN) 81
Symbology Identifier 82
Terminal 83
Terminal Window 84
Editing a Macro 87
Terminal Window Menus 88
Utilities 89
Serial Utility Commands 90
Differences from Default 91
Firmware 92
Firmware Verification 94
Device Control 95
Default/Reset/Save 96
Reader Status Request 97
General Specifications 100
MS-2 CCD Reader Dimensions 100
Appendices 101
Serial Configuration Commands 104
Serial Command Format 105
Appendix E — ASCII Table 108
Appendix F — Operational Tips 109
5 Volt Devices 110
10-28 Volt Devices 110
Hyperlink Index 115
Variable Length 124
Very Large-Scale Integration 124
Warranty 124
Recipient Response 125

Comments to this Manuals

No comments

Microscan MS-2 User Manual Page 32

Comments to this Manuals

Related products and manuals for Bar code readers Microscan MS-2